Measurement of Torque and Axial Force on Cardan Shaft

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F18%3A10239522" target="_blank" >RIV/61989100:27230/18:10239522 - isvavai.cz</a>

Výsledek na webu

<a href="https://link.springer.com/chapter/10.1007%2F978-3-030-33146-7_47" target="_blank" >https://link.springer.com/chapter/10.1007%2F978-3-030-33146-7_47</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/978-3-030-33146-7_47" target="_blank" >10.1007/978-3-030-33146-7_47</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Measurement of Torque and Axial Force on Cardan Shaft

Popis výsledku v původním jazyce

Cardan shafts are commonly used when the drive and driven shafts are not coaxial but are still parallel. If the distance between the shaft changes then the length compensation is moved under the influence of torque, the resultant friction causes an axial force to be generated between the tooth flanks in the spline. This movement can be caused by the deformation of frame or misalign-ment of shafts. The magnitude of this axial force is important for the design of other machine parts in terms of service life. This article deals with measurement of torque and axial force on cardan shaft located on machine drive. This was done to verify the magnitude of the axial forces and torque at the run of the machine due to the fatigue fracture of the bolts at the cardan flange. Article describes methodology of measurement, used equipment and evaluation method. Measured values of the axial force are compared with theoretical calculations of axial force according to the manufacture of cardan shaft.

Název v anglickém jazyce

Measurement of Torque and Axial Force on Cardan Shaft

Popis výsledku anglicky

Cardan shafts are commonly used when the drive and driven shafts are not coaxial but are still parallel. If the distance between the shaft changes then the length compensation is moved under the influence of torque, the resultant friction causes an axial force to be generated between the tooth flanks in the spline. This movement can be caused by the deformation of frame or misalign-ment of shafts. The magnitude of this axial force is important for the design of other machine parts in terms of service life. This article deals with measurement of torque and axial force on cardan shaft located on machine drive. This was done to verify the magnitude of the axial forces and torque at the run of the machine due to the fatigue fracture of the bolts at the cardan flange. Article describes methodology of measurement, used equipment and evaluation method. Measured values of the axial force are compared with theoretical calculations of axial force according to the manufacture of cardan shaft.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Lecture Notes in Mechanical Engineering. Current Methods of Construction Design

ISBN

978-3-030-33145-0

ISSN

2195-4356

e-ISSN

2195-4364

Počet stran výsledku

6

Strana od-do

409-414

Název nakladatele

Springer

Místo vydání

Cham

Místo konání akce

Demänovská Dolina

Datum konání akce

11. 9. 2018

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—