TOPOLOGICAL OPTIMIZATION OF THE ROCKER ARM

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F23%3A10252573" target="_blank" >RIV/61989100:27230/23:10252573 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mmscience.eu/journal/issues/june-2023/articles/topological-optimization-of-the-rocker-arm" target="_blank" >https://www.mmscience.eu/journal/issues/june-2023/articles/topological-optimization-of-the-rocker-arm</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17973/MMSJ.2023_06_2023036" target="_blank" >10.17973/MMSJ.2023_06_2023036</a>

Jazyk výsledku

angličtina

Název v původním jazyce

TOPOLOGICAL OPTIMIZATION OF THE ROCKER ARM

Popis výsledku v původním jazyce

The focus of this paper is to compare the results of topological optimization (TO) of the rocker arm for following 3D printing out of AISI 316L stainless steel by the Selective Laser Melting (SLM) method. We used the Altair Inspire software to optimize the shape of the rocker arm. Two variants of optimization were created, first, a variant of optimization without the Shape Control function was carried out, which resulted in a complex mechanical component with an organic shape. This bionic design means more support for the SLM method of Additive Manufacturing (AM) and worse surface quality after their removal. Therefore, a second variant of optimization was produced with the application of the Shape Control function, which positively affects manufacturability and postprocessing. The use of shape control reduced the amount of supports to a minimum, helping to improve the surface finish.

Název v anglickém jazyce

TOPOLOGICAL OPTIMIZATION OF THE ROCKER ARM

Popis výsledku anglicky

The focus of this paper is to compare the results of topological optimization (TO) of the rocker arm for following 3D printing out of AISI 316L stainless steel by the Selective Laser Melting (SLM) method. We used the Altair Inspire software to optimize the shape of the rocker arm. Two variants of optimization were created, first, a variant of optimization without the Shape Control function was carried out, which resulted in a complex mechanical component with an organic shape. This bionic design means more support for the SLM method of Additive Manufacturing (AM) and worse surface quality after their removal. Therefore, a second variant of optimization was produced with the application of the Shape Control function, which positively affects manufacturability and postprocessing. The use of shape control reduced the amount of supports to a minimum, helping to improve the surface finish.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20300 - Mechanical engineering

Projekt

<a href="/cs/project/EF17_049%2F0008407" target="_blank" >EF17_049/0008407: Inovativní a aditivní technologie výroby - nová technologická řešení 3D tisku kovů a kompozitních materiálů</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

1805-0476

Svazek periodika

2023-June

Číslo periodika v rámci svazku

June 2023

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

6545-6549

Kód UT WoS článku

001006845400001

EID výsledku v databázi Scopus

2-s2.0-85161707149