Analysis of the Impact of Changes in Thermomechanical Properties of Annealed Semi-Crystalline Plastics on the Surface Condition after the Machining Process
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F23%3A10254471" target="_blank" >RIV/61989100:27230/23:10254471 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:001028537400001" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:001028537400001</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.3390/ma16134816" target="_blank" >10.3390/ma16134816</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Analysis of the Impact of Changes in Thermomechanical Properties of Annealed Semi-Crystalline Plastics on the Surface Condition after the Machining Process
Popis výsledku v původním jazyce
In this paper, the authors present a comparative analysis of the thermomechanical properties of plastics intended for machining before and after the annealing process. The research included the dynamic properties, thermal analysis and a study of the surface after machining. The dynamic properties were tested using the DMTA method. The characteristics of changes in the value of the storage modulus E' and the tangent of the mechanical loss angle tg & delta; depending on the temperature and vibration frequency were determined. The thermal properties were tested using the DSC method, and a comparative analysis of the roughness parameters of the tested materials obtained from the profilometer was carried out. The presented studies indicate the extent of the impact of the annealing process on the machinability of structural polymer materials, taking into account the analysis of changes in the thermomechanical properties of the tested materials.
Název v anglickém jazyce
Analysis of the Impact of Changes in Thermomechanical Properties of Annealed Semi-Crystalline Plastics on the Surface Condition after the Machining Process
Popis výsledku anglicky
In this paper, the authors present a comparative analysis of the thermomechanical properties of plastics intended for machining before and after the annealing process. The research included the dynamic properties, thermal analysis and a study of the surface after machining. The dynamic properties were tested using the DMTA method. The characteristics of changes in the value of the storage modulus E' and the tangent of the mechanical loss angle tg & delta; depending on the temperature and vibration frequency were determined. The thermal properties were tested using the DSC method, and a comparative analysis of the roughness parameters of the tested materials obtained from the profilometer was carried out. The presented studies indicate the extent of the impact of the annealing process on the machinability of structural polymer materials, taking into account the analysis of changes in the thermomechanical properties of the tested materials.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/EF17_049%2F0008407" target="_blank" >EF17_049/0008407: Inovativní a aditivní technologie výroby - nová technologická řešení 3D tisku kovů a kompozitních materiálů</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2023
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Materials
ISSN
1996-1944
e-ISSN
—
Svazek periodika
16
Číslo periodika v rámci svazku
13
Stát vydavatele periodika
CH - Švýcarská konfederace
Počet stran výsledku
16
Strana od-do
—
Kód UT WoS článku
001028537400001
EID výsledku v databázi Scopus
2-s2.0-85165013943