Blank Material Influence on Stamping Springback
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F24%3A86094408" target="_blank" >RIV/61989100:27230/24:86094408 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.mmscience.eu/journal/issues/february-2024/articles/blank-material-influence-on-stamping-springback" target="_blank" >https://www.mmscience.eu/journal/issues/february-2024/articles/blank-material-influence-on-stamping-springback</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.17973/MMSJ.2024_02_2023138" target="_blank" >10.17973/MMSJ.2024_02_2023138</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Blank Material Influence on Stamping Springback
Popis výsledku v původním jazyce
Paper concerns the evaluation of blank material influence on springback of irregularly shaped stamping after drawing operation to keep the dimensions and tolerances of stamping after the drawing process which are given in part drawing. Simulation of the drawing process and consequent stamping springback were carried out by PAM-STAMP 2GTM software which uses the finite elements method, with the use of blanks from strip steels DX54D, HC220P, HX220BD and HX220YD. Two mesh strategies for drawing tool parts in the software PAM-STAMP 2GTM were compared. Stamping springback was evaluated with the use of a reference points system. Critical areas of deformations and stamping springback were evaluated. Simulation results were compared with measurements on real stampings. The most suitable strip steel in terms of achieving the minimum size of springback after stamping drawing was evaluated.
Název v anglickém jazyce
Blank Material Influence on Stamping Springback
Popis výsledku anglicky
Paper concerns the evaluation of blank material influence on springback of irregularly shaped stamping after drawing operation to keep the dimensions and tolerances of stamping after the drawing process which are given in part drawing. Simulation of the drawing process and consequent stamping springback were carried out by PAM-STAMP 2GTM software which uses the finite elements method, with the use of blanks from strip steels DX54D, HC220P, HX220BD and HX220YD. Two mesh strategies for drawing tool parts in the software PAM-STAMP 2GTM were compared. Stamping springback was evaluated with the use of a reference points system. Critical areas of deformations and stamping springback were evaluated. Simulation results were compared with measurements on real stampings. The most suitable strip steel in terms of achieving the minimum size of springback after stamping drawing was evaluated.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2024
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
MM Science Journal
ISSN
1803-1269
e-ISSN
1805-0476
Svazek periodika
17
Číslo periodika v rámci svazku
Neuveden
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
11
Strana od-do
7185-7195
Kód UT WoS článku
001193269200001
EID výsledku v databázi Scopus
2-s2.0-85198347212