Comparative Assessment of Tool Wear and Surface Topography After Superfinish Turning of Inconel 718 with Carbide and Ceramic Inserts

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F25%3A10260299" target="_blank" >RIV/61989100:27230/25:10260299 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:001474774200001" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:001474774200001</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/app15084265" target="_blank" >10.3390/app15084265</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Comparative Assessment of Tool Wear and Surface Topography After Superfinish Turning of Inconel 718 with Carbide and Ceramic Inserts

Popis výsledku v původním jazyce

Cutting inserts made of ceramic materials are used in rough machining processes of Inconel 718. This article compares sintered carbide S205 inserts with 6160 ceramic inserts after finish turning of Inconel 718 with a hardness of 45 HRC. The evaluation focused on insert wear, surface topography and changes in cutting edge radius. The results show differences in the wear of S205 and 6160 inserts. S205 inserts characterize the formation of buildup on the rake face, while 6160 inserts tend to form buildup on the flank face. Furthermore, ceramic 6160 inserts are more prone to notch wear. Surface topography analysis revealed the formation of individual high peaks on surfaces machined with ceramic inserts. The Sa parameter for all cutting conditions studied did not exceed 0.45 µm. © 2025 by the authors.

Název v anglickém jazyce

Comparative Assessment of Tool Wear and Surface Topography After Superfinish Turning of Inconel 718 with Carbide and Ceramic Inserts

Popis výsledku anglicky

Cutting inserts made of ceramic materials are used in rough machining processes of Inconel 718. This article compares sintered carbide S205 inserts with 6160 ceramic inserts after finish turning of Inconel 718 with a hardness of 45 HRC. The evaluation focused on insert wear, surface topography and changes in cutting edge radius. The results show differences in the wear of S205 and 6160 inserts. S205 inserts characterize the formation of buildup on the rake face, while 6160 inserts tend to form buildup on the flank face. Furthermore, ceramic 6160 inserts are more prone to notch wear. Surface topography analysis revealed the formation of individual high peaks on surfaces machined with ceramic inserts. The Sa parameter for all cutting conditions studied did not exceed 0.45 µm. © 2025 by the authors.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Applied Sciences

ISSN

2076-3417

e-ISSN

—

Svazek periodika

15

Číslo periodika v rámci svazku

8

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

21

Strana od-do

nestránkováno

Kód UT WoS článku

001474774200001

EID výsledku v databázi Scopus

2-s2.0-105003709549