Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

Improvement of the Asme B&pv Code Resolution ofNonplanar Flaws in Pressure Retaining Components .

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27690%2F22%3A10250515" target="_blank" >RIV/61989100:27690/22:10250515 - isvavai.cz</a>

  • Výsledek na webu

    —

  • DOI - Digital Object Identifier

    —

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    Improvement of the Asme B&pv Code Resolution ofNonplanar Flaws in Pressure Retaining Components .

  • Popis výsledku v původním jazyce

    When nonplanar flaws are detected in a component they are subjected not only to fracture mode I but to fracture modes I, II and III according to the direction of the load relatively to that of the flaws. Those fracture modes are induced by the relative displacement of crack faces as they are subjected to multi-axial loading. Consequently, the Stress Intensity Factors (SIFs) KI, KII and KIII corresponding to each of those modes should be accounted for in the flaw assessment. This is done in some Fitness-for-Service Codes that make provision to calculate an effective SIF.In the ASME B&amp;PV Code Section XI, a simplified approach is proposed: a nonplanar flaw is resolved into two planar flaws by projection of the flaw area into the planes normal to the maximum principal stresses. This approach allows simplifying the flaw assessment procedure as it deals only with KI SIF for which a lot of tabulated or closed-form solutions exist. However, the authors of this paper demonstrated recently that this simplified resolution of nonplanar flaws is not conservative for all types of loading and flaw inclinations. Consequently, an improvement of the resolution of nonplanar flaws must be provided in ASME B&amp;PV Code Section XI. In that frame, this paper carries out an exhaustive assessment of the conservatism of the ASME approach and then proposes an alternative approach to deal with nonplanar flaws allowing to overcome the non-suitability of the current ASME Code.

  • Název v anglickém jazyce

    Improvement of the Asme B&pv Code Resolution ofNonplanar Flaws in Pressure Retaining Components .

  • Popis výsledku anglicky

    When nonplanar flaws are detected in a component they are subjected not only to fracture mode I but to fracture modes I, II and III according to the direction of the load relatively to that of the flaws. Those fracture modes are induced by the relative displacement of crack faces as they are subjected to multi-axial loading. Consequently, the Stress Intensity Factors (SIFs) KI, KII and KIII corresponding to each of those modes should be accounted for in the flaw assessment. This is done in some Fitness-for-Service Codes that make provision to calculate an effective SIF.In the ASME B&amp;PV Code Section XI, a simplified approach is proposed: a nonplanar flaw is resolved into two planar flaws by projection of the flaw area into the planes normal to the maximum principal stresses. This approach allows simplifying the flaw assessment procedure as it deals only with KI SIF for which a lot of tabulated or closed-form solutions exist. However, the authors of this paper demonstrated recently that this simplified resolution of nonplanar flaws is not conservative for all types of loading and flaw inclinations. Consequently, an improvement of the resolution of nonplanar flaws must be provided in ASME B&amp;PV Code Section XI. In that frame, this paper carries out an exhaustive assessment of the conservatism of the ASME approach and then proposes an alternative approach to deal with nonplanar flaws allowing to overcome the non-suitability of the current ASME Code.

Klasifikace

  • Druh

    D - Stať ve sborníku

  • CEP obor

    —

  • OECD FORD obor

    20501 - Materials engineering

Návaznosti výsledku

  • Projekt

    Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

  • Návaznosti

    P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Ostatní

  • Rok uplatnění

    2022

  • Kód důvěrnosti údajů

    S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Údaje specifické pro druh výsledku

  • Název statě ve sborníku

    American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP. Volume 1, 2022

  • ISBN

    978-0-7918-8614-4

  • ISSN

    0277-027X

  • e-ISSN

    —

  • Počet stran výsledku

    7

  • Strana od-do

    —

  • Název nakladatele

    American Society of Mechanical Engineers

  • Místo vydání

    New York

  • Místo konání akce

    Las Vegas

  • Datum konání akce

    17. 7. 2022

  • Typ akce podle státní příslušnosti

    WRD - Celosvětová akce

  • Kód UT WoS článku

    —