Investigation of Hydrothermal Plasticization Process with Convective and Dielectric Heating
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43410%2F13%3A00210791" target="_blank" >RIV/62156489:43410/13:00210791 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Investigation of Hydrothermal Plasticization Process with Convective and Dielectric Heating
Popis výsledku v původním jazyce
In this paper time needed for convectional and dielectric heating of wood samples to the desired plasticizing temperature was experimentally determined. The temperature was measured using a contactless infrared thermometer on the surface of samples and after their splitting in the spatial center of gravity. The same temperature of the samples was achieved by dielectric heating using microwave radiation six times faster than steaming within convection. Both methods of heating have caused moisture reduction of samples. In the case of microwave heating, the decrease in moisture content was twice as much as steaming. In the second part of this study mechanical properties of samples in a plastic and reference state were measured. The samples were tested ina static three-point bend. The results did not confirm statistically significant effect of heating methods on the degree of wood plasticity. Comparison of the mechanical properties of plastic and reference samples showed the expected larg
Název v anglickém jazyce
Investigation of Hydrothermal Plasticization Process with Convective and Dielectric Heating
Popis výsledku anglicky
In this paper time needed for convectional and dielectric heating of wood samples to the desired plasticizing temperature was experimentally determined. The temperature was measured using a contactless infrared thermometer on the surface of samples and after their splitting in the spatial center of gravity. The same temperature of the samples was achieved by dielectric heating using microwave radiation six times faster than steaming within convection. Both methods of heating have caused moisture reduction of samples. In the case of microwave heating, the decrease in moisture content was twice as much as steaming. In the second part of this study mechanical properties of samples in a plastic and reference state were measured. The samples were tested ina static three-point bend. The results did not confirm statistically significant effect of heating methods on the degree of wood plasticity. Comparison of the mechanical properties of plastic and reference samples showed the expected larg
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JJ - Ostatní materiály
OECD FORD obor
—
Návaznosti výsledku
Projekt
<a href="/cs/project/EE2.3.20.0269" target="_blank" >EE2.3.20.0269: Vytvoření mezinárodního vědecko-výzkumného týmu pro vývoj nových materiálů na bázi dřeva</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2013
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Pro Ligno
ISSN
1841-4737
e-ISSN
—
Svazek periodika
9
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
RO - Rumunsko
Počet stran výsledku
9
Strana od-do
670-678
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—