Comparative Analysis of Cutting Forces in CNC Milling of MDF: The Role of Tool Coatings, Cutting Speed, and Feed Per Tooth

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43410%2F24%3A43925876" target="_blank" >RIV/62156489:43410/24:43925876 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.3390/coatings14091085" target="_blank" >https://doi.org/10.3390/coatings14091085</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/coatings14091085" target="_blank" >10.3390/coatings14091085</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Comparative Analysis of Cutting Forces in CNC Milling of MDF: The Role of Tool Coatings, Cutting Speed, and Feed Per Tooth

Popis výsledku v původním jazyce

This study investigates the influence of various tool coatings, cutting speeds, and feed per tooth values on cutting forces during the CNC milling of Medium Density Fiberboard (MDF). The coatings tested include reference, TripleSi, Hyperlox, DLC, and lapped coatings. Experiments were conducted using an SCM Morbidelli m100 CNC milling machine under controlled conditions. Cutting speeds were set at 8, 10, and 12 m/s, while feed per tooth values were varied at 0.1, 0.2, and 0.3 mm. Cutting forces were measured using a three-axis piezoelectric dynamometer Kistler, and the data were analyzed to determine the impact of these variables on cutting performance. The results revealed that while cutting speed had a minimal effect on cutting forces, feed per tooth significantly influenced them, with higher values of feed per tooth leading to increased forces. Among the coatings, lapped and TripleSi exhibited the lowest cutting forces, whereas DLC showed the highest. Statistical analysis, including ANOVA and Scheffé tests, confirmed the significant differences between the coatings and highlighted the superior performance of the lapped and TripleSi coatings in reducing cutting forces.

Název v anglickém jazyce

Comparative Analysis of Cutting Forces in CNC Milling of MDF: The Role of Tool Coatings, Cutting Speed, and Feed Per Tooth

Popis výsledku anglicky

This study investigates the influence of various tool coatings, cutting speeds, and feed per tooth values on cutting forces during the CNC milling of Medium Density Fiberboard (MDF). The coatings tested include reference, TripleSi, Hyperlox, DLC, and lapped coatings. Experiments were conducted using an SCM Morbidelli m100 CNC milling machine under controlled conditions. Cutting speeds were set at 8, 10, and 12 m/s, while feed per tooth values were varied at 0.1, 0.2, and 0.3 mm. Cutting forces were measured using a three-axis piezoelectric dynamometer Kistler, and the data were analyzed to determine the impact of these variables on cutting performance. The results revealed that while cutting speed had a minimal effect on cutting forces, feed per tooth significantly influenced them, with higher values of feed per tooth leading to increased forces. Among the coatings, lapped and TripleSi exhibited the lowest cutting forces, whereas DLC showed the highest. Statistical analysis, including ANOVA and Scheffé tests, confirmed the significant differences between the coatings and highlighted the superior performance of the lapped and TripleSi coatings in reducing cutting forces.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20502 - Paper and wood

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Coatings

ISSN

2079-6412

e-ISSN

2079-6412

Svazek periodika

14

Číslo periodika v rámci svazku

9

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

15

Strana od-do

1085

Kód UT WoS článku

001323662200001

EID výsledku v databázi Scopus

2-s2.0-85205047849