Safety audit of band saw in manufacturing organization

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43670%2F16%3A43910620" target="_blank" >RIV/62156489:43670/16:43910620 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.11118/actaun201664020467" target="_blank" >http://dx.doi.org/10.11118/actaun201664020467</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.11118/actaun201664020467" target="_blank" >10.11118/actaun201664020467</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Safety audit of band saw in manufacturing organization

Popis výsledku v původním jazyce

This paper deals with the verifying of safety status for a selected device in the manufacturing organization. The safety audit of band saw was realized in the manufacturing process. Safety requirements of the machinery for cutting material are given in the standard STN 20 0723. This standard from the point of view of the work safety defines selected requirements for sawing, cutting compounds and the using of prevention to work with cutting compounds. Among the basic requirements belong material clamping and security services for cut, band saws and jaws wear, as well as the required protective cover. The efficiency of audit in percentage was evaluated by the level of fulfilment as follows: fulfilled (A) mostly fulfilled (AB), conditionally fulfilled (B) or unfulfilled (C). Through safety audit, were defined the weaknesses that increase the degree of employee health hazard. There were proposed corrective actions to eliminate weaknesses and retraining employees. It is still needed to perform the safety audit due to reduction of the probability of occupational injury.

Název v anglickém jazyce

Safety audit of band saw in manufacturing organization

Popis výsledku anglicky

This paper deals with the verifying of safety status for a selected device in the manufacturing organization. The safety audit of band saw was realized in the manufacturing process. Safety requirements of the machinery for cutting material are given in the standard STN 20 0723. This standard from the point of view of the work safety defines selected requirements for sawing, cutting compounds and the using of prevention to work with cutting compounds. Among the basic requirements belong material clamping and security services for cut, band saws and jaws wear, as well as the required protective cover. The efficiency of audit in percentage was evaluated by the level of fulfilment as follows: fulfilled (A) mostly fulfilled (AB), conditionally fulfilled (B) or unfulfilled (C). Through safety audit, were defined the weaknesses that increase the degree of employee health hazard. There were proposed corrective actions to eliminate weaknesses and retraining employees. It is still needed to perform the safety audit due to reduction of the probability of occupational injury.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JP - Průmyslové procesy a zpracování

OECD FORD obor

—

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis

ISSN

1211-8516

e-ISSN

—

Svazek periodika

64

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

467-471

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-84969975010