Fracture toughness evaluation of a cracked au thin film by applying a finite element analysis and bulge test

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081723%3A_____%2F20%3A00533697" target="_blank" >RIV/68081723:_____/20:00533697 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/KEM.827.196" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/KEM.827.196</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/KEM.827.196" target="_blank" >10.4028/www.scientific.net/KEM.827.196</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Fracture toughness evaluation of a cracked au thin film by applying a finite element analysis and bulge test

Popis výsledku v původním jazyce

This paper presents a finite element analysis of a pre-cracked freestanding gold thin film subjected to bulge test. These tests were conducted in order to determine the elasto-plastic properties and fracture toughness of the gold films. For the experimental tests, a pre-crack was introduced in the center of the film by focused ion beam (FIB) milling with a length of 10 µ m and a width of 100nm. For the numerical fracture analysis, the problem was divided into two stages, the first stage was the development of the numerical model on the whole film without pre-crack (elasto-plastic analysis) and the second one was performed on a film portion that included the pre-crack (sub-modeling stage). Three different notches (rounded, sharp and V-sharp) were applied to calculate the stress intensity factor around the crack tip using path independent J-integral. The obtained results show that the load-deflection curves for non-cracked and pre-cracked film reproduced the experiments using the calculated elasto-plastic properties. This indicates that the proposed models presented a good correlation and robustness. Additionally, fracture toughness values were calculated between 0.288 0.5 and 0.303 MPa. m0.5 with J-integral values 1.037 J/m2 (elastic) and 1.136 J/m2 (elasto-plastic) which correspond with other calculations

Název v anglickém jazyce

Fracture toughness evaluation of a cracked au thin film by applying a finite element analysis and bulge test

Popis výsledku anglicky

This paper presents a finite element analysis of a pre-cracked freestanding gold thin film subjected to bulge test. These tests were conducted in order to determine the elasto-plastic properties and fracture toughness of the gold films. For the experimental tests, a pre-crack was introduced in the center of the film by focused ion beam (FIB) milling with a length of 10 µ m and a width of 100nm. For the numerical fracture analysis, the problem was divided into two stages, the first stage was the development of the numerical model on the whole film without pre-crack (elasto-plastic analysis) and the second one was performed on a film portion that included the pre-crack (sub-modeling stage). Three different notches (rounded, sharp and V-sharp) were applied to calculate the stress intensity factor around the crack tip using path independent J-integral. The obtained results show that the load-deflection curves for non-cracked and pre-cracked film reproduced the experiments using the calculated elasto-plastic properties. This indicates that the proposed models presented a good correlation and robustness. Additionally, fracture toughness values were calculated between 0.288 0.5 and 0.303 MPa. m0.5 with J-integral values 1.037 J/m2 (elastic) and 1.136 J/m2 (elasto-plastic) which correspond with other calculations

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20506 - Coating and films

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Key Engineering Materials

ISBN

978-3-0357-1586-6

ISSN

1013-9826

e-ISSN

—

Počet stran výsledku

7

Strana od-do

196-202

Název nakladatele

Trans Tech Publication

Místo vydání

Zurich

Místo konání akce

Rhodos

Datum konání akce

16. 9. 2019

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—