Fabrication and Performance Testing of Composite Molybdenum: “Resinpal 2301” Field Emission Emitters

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081731%3A_____%2F24%3A00588162" target="_blank" >RIV/68081731:_____/24:00588162 - isvavai.cz</a>

Výsledek na webu

<a href="https://jjp.yu.edu.jo/index.php/jjp/article/view/335" target="_blank" >https://jjp.yu.edu.jo/index.php/jjp/article/view/335</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.47011/17.2.9" target="_blank" >10.47011/17.2.9</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Fabrication and Performance Testing of Composite Molybdenum: “Resinpal 2301” Field Emission Emitters

Popis výsledku v původním jazyce

Over the past few decades, epoxy resins have shown several advantages as coating materials for field emission electron sources, this includes lowering the operation applied voltages and the threshold voltage required to start the electron emission process. This study illustrates the results of using the Resinpal 2301 epoxy resin as a coating material for field emission emitters. The results include the ultraviolet photoelectron spectroscopy analysis to obtain an average value for the local work function and ionization energy for the cured coating layer. The samples were checked using scanning electron microscopy before and after being coated with the cured epoxy resin. Moreover, the field emission microscopy characteristics of both uncoated molybdenum and composite molybdenum-epoxy samples are presented in the form of a comprehensive comparison. The study shows promising results in enhancing the field emission characteristics with the application of the coating material. Notably, there was a significant reduction in the threshold voltage. The emission current values from coated samples were found to be at least ~11 times higher than those from uncoated samples. (c) 2024 Yarmouk University. All rights reserved.

Název v anglickém jazyce

Fabrication and Performance Testing of Composite Molybdenum: “Resinpal 2301” Field Emission Emitters

Popis výsledku anglicky

Over the past few decades, epoxy resins have shown several advantages as coating materials for field emission electron sources, this includes lowering the operation applied voltages and the threshold voltage required to start the electron emission process. This study illustrates the results of using the Resinpal 2301 epoxy resin as a coating material for field emission emitters. The results include the ultraviolet photoelectron spectroscopy analysis to obtain an average value for the local work function and ionization energy for the cured coating layer. The samples were checked using scanning electron microscopy before and after being coated with the cured epoxy resin. Moreover, the field emission microscopy characteristics of both uncoated molybdenum and composite molybdenum-epoxy samples are presented in the form of a comprehensive comparison. The study shows promising results in enhancing the field emission characteristics with the application of the coating material. Notably, there was a significant reduction in the threshold voltage. The emission current values from coated samples were found to be at least ~11 times higher than those from uncoated samples. (c) 2024 Yarmouk University. All rights reserved.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20201 - Electrical and electronic engineering

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Jordan Journal of Physics

ISSN

1994-7607

e-ISSN

1994-7615

Svazek periodika

17

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

JO - Jordánské hášimovské království

Počet stran výsledku

15

Strana od-do

217-231

Kód UT WoS článku

001282328100009

EID výsledku v databázi Scopus

2-s2.0-85199948949