Determination of vibration frequency depending on abrasive mass flow rate during abrasive water jet cutting

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68145535%3A_____%2F14%3A00433786" target="_blank" >RIV/68145535:_____/14:00433786 - isvavai.cz</a>

Výsledek na webu

<a href="http://link.springer.com/article/10.1007%2Fs00170-014-6497-9#page-1" target="_blank" >http://link.springer.com/article/10.1007%2Fs00170-014-6497-9#page-1</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s00170-014-6497-9" target="_blank" >10.1007/s00170-014-6497-9</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Determination of vibration frequency depending on abrasive mass flow rate during abrasive water jet cutting

Popis výsledku v původním jazyce

The paper deals with the determination of vibration emission frequency depending on the impact of abrasive particles during cutting of materials. In order to verify the investigated hypothesis, the factor of the abrasive mass flow rate m a ?=?250 and 400g min1 at the traverse speed of cutting head v?=?50, 75, 100 and 150 mm min1 was determined. The Barton Garnet with MESH 80 and focusing tube with diameter of 0.8 and 1.4 mm were used in the experiment. Vibrations were recorded during experimental cutting by sensors PCB IMI type 607A11 placed on the stainless steel AISI 309. During the experimental sample cutting, vibrations were monitored and consequently processed by the LabVIEW 8.5 software. Research results are useful for improving the quality of surface created by abrasive water jet, and they can encourage the on-line process control of abrasive water jet cutting with the minimum human intervention in case of a fault or error during the supply of abrasives to cutting head.

Název v anglickém jazyce

Determination of vibration frequency depending on abrasive mass flow rate during abrasive water jet cutting

Popis výsledku anglicky

The paper deals with the determination of vibration emission frequency depending on the impact of abrasive particles during cutting of materials. In order to verify the investigated hypothesis, the factor of the abrasive mass flow rate m a ?=?250 and 400g min1 at the traverse speed of cutting head v?=?50, 75, 100 and 150 mm min1 was determined. The Barton Garnet with MESH 80 and focusing tube with diameter of 0.8 and 1.4 mm were used in the experiment. Vibrations were recorded during experimental cutting by sensors PCB IMI type 607A11 placed on the stainless steel AISI 309. During the experimental sample cutting, vibrations were monitored and consequently processed by the LabVIEW 8.5 software. Research results are useful for improving the quality of surface created by abrasive water jet, and they can encourage the on-line process control of abrasive water jet cutting with the minimum human intervention in case of a fault or error during the supply of abrasives to cutting head.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JQ - Strojní zařízení a nástroje

OECD FORD obor

—

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

International Journal of Advanced Manufacturing Technology

ISSN

0268-3768

e-ISSN

—

Svazek periodika

77

Číslo periodika v rámci svazku

1-4

Stát vydavatele periodika

DE - Spolková republika Německo

Počet stran výsledku

12

Strana od-do

763-774

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—