The effect of hydrothermal curing on residual mechanical properties of refractory concrete
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F18%3A00322812" target="_blank" >RIV/68407700:21110/18:00322812 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.1063/1.5043882" target="_blank" >http://dx.doi.org/10.1063/1.5043882</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1063/1.5043882" target="_blank" >10.1063/1.5043882</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
The effect of hydrothermal curing on residual mechanical properties of refractory concrete
Popis výsledku v původním jazyce
This paper describes the influence of hydrothermal curing conditions on final mechanical properties of refractory fibre-reinforced cement composite. The effect of age of specimens, when the hydrothermal curing process started, was investigated in the point of view of best achieved mechanical properties. The age of 24, 30, 36, 42 and 48 hours after fist contact water with cement was tested. The curing conditions in autoclave device were set on 150 °C and 0.45 MPa in 100% humidity environment. Hydrothermally cured specimens together with reference specimens cured in laboratory conditions were exposed to the action of elevated temperature on level 600°C and 1000°C for three hours. The dynamic modulus of elasticity, flexural strength, compressive strength and bulk density were measured to quantify the benefit of hydrothermal curing. Used refractory composite consisted of natural basalt aggregate, aluminous cement, fine ground ceramic powder, water with plasticizer and basalt fibres. All parameters were investigated on specimens with dimension 40 x 40 x 160 mm. The specimens activated in autoclave achieved higher residual properties compared with reference specimens cured in laboratory conditions. The cohesion between hydration products and fibreś surface increases due to the influence of hydrothermal conditions.
Název v anglickém jazyce
The effect of hydrothermal curing on residual mechanical properties of refractory concrete
Popis výsledku anglicky
This paper describes the influence of hydrothermal curing conditions on final mechanical properties of refractory fibre-reinforced cement composite. The effect of age of specimens, when the hydrothermal curing process started, was investigated in the point of view of best achieved mechanical properties. The age of 24, 30, 36, 42 and 48 hours after fist contact water with cement was tested. The curing conditions in autoclave device were set on 150 °C and 0.45 MPa in 100% humidity environment. Hydrothermally cured specimens together with reference specimens cured in laboratory conditions were exposed to the action of elevated temperature on level 600°C and 1000°C for three hours. The dynamic modulus of elasticity, flexural strength, compressive strength and bulk density were measured to quantify the benefit of hydrothermal curing. Used refractory composite consisted of natural basalt aggregate, aluminous cement, fine ground ceramic powder, water with plasticizer and basalt fibres. All parameters were investigated on specimens with dimension 40 x 40 x 160 mm. The specimens activated in autoclave achieved higher residual properties compared with reference specimens cured in laboratory conditions. The cohesion between hydration products and fibreś surface increases due to the influence of hydrothermal conditions.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20101 - Civil engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/GBP105%2F12%2FG059" target="_blank" >GBP105/12/G059: Kumulativní časově závislé procesy ve stavebních materiálech a konstrukcích</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
Proceedings of International Conference on Numerical Analysis and Applied Mathematics 2017 (ICNAAM-2017)
ISBN
978-0-7354-1690-1
ISSN
—
e-ISSN
0094-243X
Počet stran výsledku
4
Strana od-do
—
Název nakladatele
AIP Conference Proceedings
Místo vydání
New York
Místo konání akce
Thessaloniki
Datum konání akce
25. 9. 2017
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
000445105400214