Enhanced static and fatigue performance of FDM 3D-printed polycarbonate adhesive joints using bio-inspired surface textures

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21110%2F25%3A00383348" target="_blank" >RIV/68407700:21110/25:00383348 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.1016/j.engfailanal.2025.109626" target="_blank" >https://doi.org/10.1016/j.engfailanal.2025.109626</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.engfailanal.2025.109626" target="_blank" >10.1016/j.engfailanal.2025.109626</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Enhanced static and fatigue performance of FDM 3D-printed polycarbonate adhesive joints using bio-inspired surface textures

Popis výsledku v původním jazyce

The bonding potential of additively manufactured polycarbonate (PC) material is still a relatively unexplored area, and the addition of bio-inspired surface texture to enhance adhesion, particularly concerning fatigue performance, has not yet been investigated. This study examines the effects of bio-surface texture on the static and fatigue strength of 3D-printed PC adhesive joints. The methodology involved firstly designing and 3D-printing substrates with as-printed and textured surfaces, inspired by the Tree Frog toe pads (TF) and Fish Scales (FS) surfaces. Subsequently, static and fatigue tensile tests were performed using Arcan joints, while the block shear method was adopted for the fatigue shear tests. The findings indicated that TF and FS textures significantly enhanced static tensile strength and extended both tensile and shear fatigue life by promoting mechanical interlocking and increasing the effective contact area, compared to the as-printed texture. Specifically, the TF and FS textures increased the static tensile strength by 51% and 31%, respectively. Under constant maximum fatigue loading conditions, TF and FS textures extended tensile fatigue life by 266 and 173 times, and shear fatigue life by 134 and 65 times. Moreover, adhesive joints with bio-inspired surfaces exhibit greater resistance than bulk adherends due to the increased sensitivity of 3D-printed adherends to defects, particularly voids, under cyclic loading. Therefore, to improve the static and fatigue resistance of 3D-printed PC adhesive joints, it is advisable to apply the load perpendicularly to the parts’ build orientation, design joints to withstand shear loads and include TF bio-texture on adherend surfaces.

Název v anglickém jazyce

Enhanced static and fatigue performance of FDM 3D-printed polycarbonate adhesive joints using bio-inspired surface textures

Popis výsledku anglicky

The bonding potential of additively manufactured polycarbonate (PC) material is still a relatively unexplored area, and the addition of bio-inspired surface texture to enhance adhesion, particularly concerning fatigue performance, has not yet been investigated. This study examines the effects of bio-surface texture on the static and fatigue strength of 3D-printed PC adhesive joints. The methodology involved firstly designing and 3D-printing substrates with as-printed and textured surfaces, inspired by the Tree Frog toe pads (TF) and Fish Scales (FS) surfaces. Subsequently, static and fatigue tensile tests were performed using Arcan joints, while the block shear method was adopted for the fatigue shear tests. The findings indicated that TF and FS textures significantly enhanced static tensile strength and extended both tensile and shear fatigue life by promoting mechanical interlocking and increasing the effective contact area, compared to the as-printed texture. Specifically, the TF and FS textures increased the static tensile strength by 51% and 31%, respectively. Under constant maximum fatigue loading conditions, TF and FS textures extended tensile fatigue life by 266 and 173 times, and shear fatigue life by 134 and 65 times. Moreover, adhesive joints with bio-inspired surfaces exhibit greater resistance than bulk adherends due to the increased sensitivity of 3D-printed adherends to defects, particularly voids, under cyclic loading. Therefore, to improve the static and fatigue resistance of 3D-printed PC adhesive joints, it is advisable to apply the load perpendicularly to the parts’ build orientation, design joints to withstand shear loads and include TF bio-texture on adherend surfaces.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Engineering Failure Analysis

ISSN

1350-6307

e-ISSN

1873-1961

Svazek periodika

176

Číslo periodika v rámci svazku

July

Stát vydavatele periodika

NL - Nizozemsko

Počet stran výsledku

22

Strana od-do

—

Kód UT WoS článku

001478531400001

EID výsledku v databázi Scopus

2-s2.0-105003170077