Tin coating of connectors - reliability risk for electrical equipment
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68407700%3A21230%2F11%3A00183627" target="_blank" >RIV/68407700:21230/11:00183627 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.1109/ISSE.2011.6053864" target="_blank" >http://dx.doi.org/10.1109/ISSE.2011.6053864</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1109/ISSE.2011.6053864" target="_blank" >10.1109/ISSE.2011.6053864</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Tin coating of connectors - reliability risk for electrical equipment
Popis výsledku v původním jazyce
The EC directive 2002/95/ES (RoHS) limited (with few exceptions) the use of lead in electronic production, especially in solders and surface finishes. This brought significant changes in their reliability. The electroplated tin coating is currently amongthe most widely used surface finishes in the electronic industry, appearing everywhere from the coating of solder pads on SMD devices to corrosion prevention coating on large containers. The tin is usually deposited galvanically, in a layer 10mm thick,often with a yet thinner interlayer between the tin and base material. The most common base materials are copper, brass and bronze. Usually the connector or component lead is cut, bent or otherwise shaped either before the coating or after it. This combination of materials and mechanical stress can lead to appearance of one important risk factor: tin whiskers.
Název v anglickém jazyce
Tin coating of connectors - reliability risk for electrical equipment
Popis výsledku anglicky
The EC directive 2002/95/ES (RoHS) limited (with few exceptions) the use of lead in electronic production, especially in solders and surface finishes. This brought significant changes in their reliability. The electroplated tin coating is currently amongthe most widely used surface finishes in the electronic industry, appearing everywhere from the coating of solder pads on SMD devices to corrosion prevention coating on large containers. The tin is usually deposited galvanically, in a layer 10mm thick,often with a yet thinner interlayer between the tin and base material. The most common base materials are copper, brass and bronze. Usually the connector or component lead is cut, bent or otherwise shaped either before the coating or after it. This combination of materials and mechanical stress can lead to appearance of one important risk factor: tin whiskers.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
JA - Elektronika a optoelektronika, elektrotechnika
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2011
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
34th International Spring Seminar on Electronics Technology
ISBN
978-1-4577-2111-3
ISSN
—
e-ISSN
—
Počet stran výsledku
5
Strana od-do
229-233
Název nakladatele
Technical University of Košice
Místo vydání
Košice
Místo konání akce
Tatranská Lomnica
Datum konání akce
11. 5. 2011
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
—