Influence of nano-filler type on technological processing and resulting mechanical properties

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F19%3A63522856" target="_blank" >RIV/70883521:28110/19:63522856 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.scientific.net/MSF.952.180" target="_blank" >https://www.scientific.net/MSF.952.180</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/MSF.952.180" target="_blank" >10.4028/www.scientific.net/MSF.952.180</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of nano-filler type on technological processing and resulting mechanical properties

Popis výsledku v původním jazyce

Modification of polymers by fillers is one of the most used material alterations to improve its required properties. This article is about modification of polymer matrix by fillers with layered particles. Linear low density polyethylene (LLDPE) was used as matrix and it was mixed with different kinds of fillers. Fillers used were: CaPhP – Calcium Phenylphosphonate, double layered hydroxides (ZnAl-DDS, ZnAl-lac and ZnAl-CO3) and natural Talc. Individual fillers were mixed into the matrix by kneading machine with the use of several velocities. The article focuses on influence of the individual filler on mechanical properties measured by tensile strength test. This paper also investigates the problem of process parameters’ influence on final mechanical properties and later confirms positive impact of all fillers that were used, although the size of them differs.

Název v anglickém jazyce

Influence of nano-filler type on technological processing and resulting mechanical properties

Popis výsledku anglicky

Modification of polymers by fillers is one of the most used material alterations to improve its required properties. This article is about modification of polymer matrix by fillers with layered particles. Linear low density polyethylene (LLDPE) was used as matrix and it was mixed with different kinds of fillers. Fillers used were: CaPhP – Calcium Phenylphosphonate, double layered hydroxides (ZnAl-DDS, ZnAl-lac and ZnAl-CO3) and natural Talc. Individual fillers were mixed into the matrix by kneading machine with the use of several velocities. The article focuses on influence of the individual filler on mechanical properties measured by tensile strength test. This paper also investigates the problem of process parameters’ influence on final mechanical properties and later confirms positive impact of all fillers that were used, although the size of them differs.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials Science Forum

ISSN

0255-5476

e-ISSN

—

Svazek periodika

952

Číslo periodika v rámci svazku

Neuvedeno

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

8

Strana od-do

180-187

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85066282242