Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

Secondary biaxial data application in a process of a hyperelastic material characterization

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F19%3A63523533" target="_blank" >RIV/70883521:28110/19:63523533 - isvavai.cz</a>

  • Výsledek na webu

    <a href="https://www.scientific.net/MSF.952.275" target="_blank" >https://www.scientific.net/MSF.952.275</a>

  • DOI - Digital Object Identifier

    <a href="http://dx.doi.org/10.4028/www.scientific.net/MSF.952.275" target="_blank" >10.4028/www.scientific.net/MSF.952.275</a>

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    Secondary biaxial data application in a process of a hyperelastic material characterization

  • Popis výsledku v původním jazyce

    In order to find hyperelastic material model constants, data fitting technique is often used. For this task, the data is collected through different laboratory tests, namely, the uniaxial, the biaxial and the pure shear. However, due to the difficulty in getting biaxial data, often only uniaxial data was used for the fitting. Despite frequent use, it was established that this practice creates erroneous results. With a view to improve the data fitting results and at the same time to overcome the difficulty of collecting primary biaxial data, uniaxial data was used to generate a secondary biaxial data set. The data derived through this method was then tested with four common models as to examine the compatibility of the method. Subsequently, real biaxial data was used to compare with the data fitting results obtained through the proposed method. As results indicated combined data fitting for both instances were very much identical with respect to all tested models. Cases where somewhat higher deviation observed between experimental curves and data fitted curves for biaxial data, gave similar results for adjusted data driven data fitting too. However, such deviation could be attributed to mismatch between models with the particular material behaviour rather than the generated data.

  • Název v anglickém jazyce

    Secondary biaxial data application in a process of a hyperelastic material characterization

  • Popis výsledku anglicky

    In order to find hyperelastic material model constants, data fitting technique is often used. For this task, the data is collected through different laboratory tests, namely, the uniaxial, the biaxial and the pure shear. However, due to the difficulty in getting biaxial data, often only uniaxial data was used for the fitting. Despite frequent use, it was established that this practice creates erroneous results. With a view to improve the data fitting results and at the same time to overcome the difficulty of collecting primary biaxial data, uniaxial data was used to generate a secondary biaxial data set. The data derived through this method was then tested with four common models as to examine the compatibility of the method. Subsequently, real biaxial data was used to compare with the data fitting results obtained through the proposed method. As results indicated combined data fitting for both instances were very much identical with respect to all tested models. Cases where somewhat higher deviation observed between experimental curves and data fitted curves for biaxial data, gave similar results for adjusted data driven data fitting too. However, such deviation could be attributed to mismatch between models with the particular material behaviour rather than the generated data.

Klasifikace

  • Druh

    J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS

  • CEP obor

  • OECD FORD obor

    20501 - Materials engineering

Návaznosti výsledku

  • Projekt

  • Návaznosti

    V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Ostatní

  • Rok uplatnění

    2019

  • Kód důvěrnosti údajů

    S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Údaje specifické pro druh výsledku

  • Název periodika

    Materials Science Forum

  • ISSN

    0255-5476

  • e-ISSN

  • Svazek periodika

    952

  • Číslo periodika v rámci svazku

    Neuveden

  • Stát vydavatele periodika

    CH - Švýcarská konfederace

  • Počet stran výsledku

    7

  • Strana od-do

    275-281

  • Kód UT WoS článku

  • EID výsledku v databázi Scopus

    2-s2.0-85066294926