Possibility of Utilization of Gate Geometry to Modify the Mechanical and Structural Properties of Castings on the Al-Si Basis
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F75081431%3A_____%2F20%3A00001801" target="_blank" >RIV/75081431:_____/20:00001801 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.mdpi.com/1996-1944/13/16/3539" target="_blank" >https://www.mdpi.com/1996-1944/13/16/3539</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.3390/MA13163539" target="_blank" >10.3390/MA13163539</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Possibility of Utilization of Gate Geometry to Modify the Mechanical and Structural Properties of Castings on the Al-Si Basis
Popis výsledku v původním jazyce
The mechanical properties of die castings correlate with the inner structure of a casting, distribution of the eutectic phases, and with the content and distribution of porous cavities in the casting volume. This submitted paper deals with the issue of the possibility to influence the basic parameters affecting the quality of castings through structural modifications of the gating system. The structural parameter under assessment is the gate height. In the case of the diverse height of the gate, five sets of castings were produced. The individual sets of castings were subjected to examination of selected mechanical properties, i.e., of permanent deformation and surface hardness. At the same time, the individual sets of castings were subjected to metallographic examination of the eutectic structure of the casting. It was proved that the gate height influences the aforementioned properties of the castings and significantly affects the ratio of the eutectic phases in the volume of the casting. The conclusion describes the mutual correlation between the gate structure, the mechanical properties of the casting, and its structural composition.
Název v anglickém jazyce
Possibility of Utilization of Gate Geometry to Modify the Mechanical and Structural Properties of Castings on the Al-Si Basis
Popis výsledku anglicky
The mechanical properties of die castings correlate with the inner structure of a casting, distribution of the eutectic phases, and with the content and distribution of porous cavities in the casting volume. This submitted paper deals with the issue of the possibility to influence the basic parameters affecting the quality of castings through structural modifications of the gating system. The structural parameter under assessment is the gate height. In the case of the diverse height of the gate, five sets of castings were produced. The individual sets of castings were subjected to examination of selected mechanical properties, i.e., of permanent deformation and surface hardness. At the same time, the individual sets of castings were subjected to metallographic examination of the eutectic structure of the casting. It was proved that the gate height influences the aforementioned properties of the castings and significantly affects the ratio of the eutectic phases in the volume of the casting. The conclusion describes the mutual correlation between the gate structure, the mechanical properties of the casting, and its structural composition.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20300 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
V - Vyzkumna aktivita podporovana z jinych verejnych zdroju
Ostatní
Rok uplatnění
2020
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Materials
ISSN
1996-1944
e-ISSN
—
Svazek periodika
13
Číslo periodika v rámci svazku
16
Stát vydavatele periodika
CH - Švýcarská konfederace
Počet stran výsledku
2
Strana od-do
—
Kód UT WoS článku
000564807800001
EID výsledku v databázi Scopus
2-s2.0-85090028677