Analysis of the Mechanical Properties of the AlSi7CrMnCu2.5 alloy and their Changes after Heat Treatment

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F25%3A43899659" target="_blank" >RIV/44555601:13420/25:43899659 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/1996-1944/18/19/4586" target="_blank" >https://www.mdpi.com/1996-1944/18/19/4586</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma18194586" target="_blank" >10.3390/ma18194586</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Analysis of the Mechanical Properties of the AlSi7CrMnCu2.5 alloy and their Changes after Heat Treatment

Popis výsledku v původním jazyce

The article deals with the analysis of the mechanical properties of the newly designed aluminum alloy Al-Si7CrMnCu2.5. The research was carried out in order to map a new alloy with a certain addition of chromium and manganese from the point of view of mechanical properties and their changes after heat treatment (hardening, artificial aging) with defined parameters. Specifically, properties such as strength limit, yield strength, ductility, hardness, and microhardness were analyzed, both in the cast state and after heat treatment. The alloy was designed as an alternative to the standard Al-Si alloys already used in practice (AlSi7Mg, AlSi7Mg0.3, AlSi8Cu2Mn, AlSi8Cu3), which are mainly used in the production of engine parts and other components for the automotive and aviation industries. As can be seen from the presented results, the experimental AlSi7CrMnCu2.5 alloy exceeds the properties of the other selected alloys by tens of percent already in the cast state in many parameters. After heat treatment, the results achieved are comparable to the mentioned alloys, and in most cases, their values exceed them, especially in terms of ductility and hardness.

Název v anglickém jazyce

Analysis of the Mechanical Properties of the AlSi7CrMnCu2.5 alloy and their Changes after Heat Treatment

Popis výsledku anglicky

The article deals with the analysis of the mechanical properties of the newly designed aluminum alloy Al-Si7CrMnCu2.5. The research was carried out in order to map a new alloy with a certain addition of chromium and manganese from the point of view of mechanical properties and their changes after heat treatment (hardening, artificial aging) with defined parameters. Specifically, properties such as strength limit, yield strength, ductility, hardness, and microhardness were analyzed, both in the cast state and after heat treatment. The alloy was designed as an alternative to the standard Al-Si alloys already used in practice (AlSi7Mg, AlSi7Mg0.3, AlSi8Cu2Mn, AlSi8Cu3), which are mainly used in the production of engine parts and other components for the automotive and aviation industries. As can be seen from the presented results, the experimental AlSi7CrMnCu2.5 alloy exceeds the properties of the other selected alloys by tens of percent already in the cast state in many parameters. After heat treatment, the results achieved are comparable to the mentioned alloys, and in most cases, their values exceed them, especially in terms of ductility and hardness.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

1996-1944

Svazek periodika

18

Číslo periodika v rámci svazku

19

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

11

Strana od-do

1-11

Kód UT WoS článku

001593793200001

EID výsledku v databázi Scopus

—