The Effect of Mechanical Surface Pre-treatment on the Strength of the Adhesive Joint of High Strength Sheets
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24210%2F19%3A00007690" target="_blank" >RIV/46747885:24210/19:00007690 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/46747885:24510/19:00007690
Výsledek na webu
<a href="http://The" target="_blank" >http://The</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1088/1757-899X/723/1/012013" target="_blank" >10.1088/1757-899X/723/1/012013</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
The Effect of Mechanical Surface Pre-treatment on the Strength of the Adhesive Joint of High Strength Sheets
Popis výsledku v původním jazyce
Nowadays, in the car body parts production, the quenching is often replaced by adhesive joints. The adhesive joints have a lot of advantages – they allow to keep the protective layer, enable to join different material and prevent from the formation of heat affected zones. With respect to passenger’s passive safety, plenty of car body parts are manufactured of high strength steel sheets. The body parts are hot-formed at a temperature of 900 °C to the desired shape followed by subsequent rapid quenching to achieve the required strength. The sheets are covered with an AlSi 60/60 layer which should protect them from high-temperature oxidation during the forming process. However, brittle intermetallic interlayers form during the hightemperature treatment due to the reaction of iron from the substrate with Al/Si from the protective cover, which negatively affects the final strength of adhesion joint. The paper deals with the comparison of different possible ways of removing the layer on the final strength
Název v anglickém jazyce
The Effect of Mechanical Surface Pre-treatment on the Strength of the Adhesive Joint of High Strength Sheets
Popis výsledku anglicky
Nowadays, in the car body parts production, the quenching is often replaced by adhesive joints. The adhesive joints have a lot of advantages – they allow to keep the protective layer, enable to join different material and prevent from the formation of heat affected zones. With respect to passenger’s passive safety, plenty of car body parts are manufactured of high strength steel sheets. The body parts are hot-formed at a temperature of 900 °C to the desired shape followed by subsequent rapid quenching to achieve the required strength. The sheets are covered with an AlSi 60/60 layer which should protect them from high-temperature oxidation during the forming process. However, brittle intermetallic interlayers form during the hightemperature treatment due to the reaction of iron from the substrate with Al/Si from the protective cover, which negatively affects the final strength of adhesion joint. The paper deals with the comparison of different possible ways of removing the layer on the final strength
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20506 - Coating and films
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2019
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
IOP Conference Series: Materials Science and Engineering
ISBN
—
ISSN
1757-8981
e-ISSN
—
Počet stran výsledku
8
Strana od-do
—
Název nakladatele
Institute of Physics Publishing
Místo vydání
Bristol
Místo konání akce
Plzeň
Datum konání akce
1. 1. 2019
Typ akce podle státní příslušnosti
EUR - Evropská akce
Kód UT WoS článku
—