Influence of Cutting Conditions on the Surface Quality and Grinding Wheel Wear during Cylindrical Grinding of Inconel 718

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F17%3A43949634" target="_blank" >RIV/49777513:23210/17:43949634 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.daaam.info/Downloads/Pdfs/proceedings/proceedings_2017/070.pdf" target="_blank" >http://www.daaam.info/Downloads/Pdfs/proceedings/proceedings_2017/070.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.2507/28th.daaam.proceedings.070" target="_blank" >10.2507/28th.daaam.proceedings.070</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of Cutting Conditions on the Surface Quality and Grinding Wheel Wear during Cylindrical Grinding of Inconel 718

Popis výsledku v původním jazyce

This article deals with the experimental grinding of Inconel 718. This material is used for highly stressed components in the nuclear industry, such as combustion turbines. The material is very problematic for machining due to its rapid hardening and high heat generation. Two types of Inconel 718 in the form of testing bars were finished by cylindrical grinding using different cutting conditions and strategies. The main aim is to determine the impact of grinding conditions on the surface quality in terms of surface roughness after grinding. The resulting surface was scanned using an optical-scanning device to observe the topography of the ground surface. The grinding wheel was measured after grinding each bar to observe the wheel wear and the changes of the grinding wheel shape. The spindle load was monitored during grinding to see the effect of different strategies on the grinding process. The results from this work will be used in further studies and contribute to a better understanding of grinding Inconel 718.

Název v anglickém jazyce

Influence of Cutting Conditions on the Surface Quality and Grinding Wheel Wear during Cylindrical Grinding of Inconel 718

Popis výsledku anglicky

This article deals with the experimental grinding of Inconel 718. This material is used for highly stressed components in the nuclear industry, such as combustion turbines. The material is very problematic for machining due to its rapid hardening and high heat generation. Two types of Inconel 718 in the form of testing bars were finished by cylindrical grinding using different cutting conditions and strategies. The main aim is to determine the impact of grinding conditions on the surface quality in terms of surface roughness after grinding. The resulting surface was scanned using an optical-scanning device to observe the topography of the ground surface. The grinding wheel was measured after grinding each bar to observe the wheel wear and the changes of the grinding wheel shape. The spindle load was monitored during grinding to see the effect of different strategies on the grinding process. The results from this work will be used in further studies and contribute to a better understanding of grinding Inconel 718.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/TG02010011" target="_blank" >TG02010011: Podpora komerčních příležitostí ZČU</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Proceedings of the 28th DAAAM International Symposium

ISBN

978-3-902734-11-2

ISSN

1726-9679

e-ISSN

neuvedeno

Počet stran výsledku

6

Strana od-do

500-505

Název nakladatele

DAAAM International

Místo vydání

Vienna

Místo konání akce

Zadar

Datum konání akce

8. 11. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—