Degradation of a Grinding Wheel when Grinding Cermet Materials and Its Influence on the Grinding Process

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F19%3A43953979" target="_blank" >RIV/49777513:23210/19:43953979 - isvavai.cz</a>

Výsledek na webu

<a href="https://arl.ujep.cz/arl-ujep/cs/csg/?repo=ujeprepo&key=22900557702" target="_blank" >https://arl.ujep.cz/arl-ujep/cs/csg/?repo=ujeprepo&key=22900557702</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/236.2019/a/1213-2489/mt/19/1/9" target="_blank" >10.21062/ujep/236.2019/a/1213-2489/mt/19/1/9</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Degradation of a Grinding Wheel when Grinding Cermet Materials and Its Influence on the Grinding Process

Popis výsledku v původním jazyce

This article deals with the experimental grinding of cermet materials. Two types of cermet materials from different suppliers were ground under constant grinding conditions using a diamond grinding wheel. The main aim was to determine the influence of the grinding on the degradation of the grinding wheel and changes in the grinding process. Both types of cermet were ground with the same strategy and the same number of passes. The grinding wheel was analysed during grinding using an optical scanning device to observe the changes on the grinding wheel surface. Clogging and wear of the grinding wheel occurred on the surface as the amount of material removed increased. All grinding tests were carried out without dressing or truing of the grinding wheel. Degradation of the grinding wheel had a big influence on the grinding process in terms of the spindle load during grinding. The roughness of the ground surface was also measured using the optical scanning device. The results from this work will be used for further research of cermet grinding.

Název v anglickém jazyce

Degradation of a Grinding Wheel when Grinding Cermet Materials and Its Influence on the Grinding Process

Popis výsledku anglicky

This article deals with the experimental grinding of cermet materials. Two types of cermet materials from different suppliers were ground under constant grinding conditions using a diamond grinding wheel. The main aim was to determine the influence of the grinding on the degradation of the grinding wheel and changes in the grinding process. Both types of cermet were ground with the same strategy and the same number of passes. The grinding wheel was analysed during grinding using an optical scanning device to observe the changes on the grinding wheel surface. Clogging and wear of the grinding wheel occurred on the surface as the amount of material removed increased. All grinding tests were carried out without dressing or truing of the grinding wheel. Degradation of the grinding wheel had a big influence on the grinding process in terms of the spindle load during grinding. The roughness of the ground surface was also measured using the optical scanning device. The results from this work will be used for further research of cermet grinding.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/LO1502" target="_blank" >LO1502: Rozvoj Regionálního technologického institutu</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

19

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

9-13

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85063324758