Measurement of tensile force at the fundamental tillage using tractor?s build -in sensor and external sensor connected between machines and their comparison

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41210%2F15%3A67269" target="_blank" >RIV/60460709:41210/15:67269 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/60460709:41310/15:67269

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Measurement of tensile force at the fundamental tillage using tractor?s build -in sensor and external sensor connected between machines and their comparison

Popis výsledku v původním jazyce

The value of tensile force during soil tillage is crucial for estimation of the energy performance of trailed machines. For tensile force measurements was used mouldboard plough with working width of 4 m. The ploughing speed was approximately 7 kmh-1. The measurement was carried out on two plots that showed different soil texture. On the first plot dominate loam-sandy soil whereas on the second plot clay soil, the slopes of the plots are 1,1 and 2,4 respectively. Both plots have been left without modification of stubble after harvest. To measure the tensile forces was used the dynamometer LUKAS type S-38. Dynamometer was placed in a hinge, which was positioned between two tractors. As a second method of tensile force measurement was used from electro-hydraulic hitch sensors from where the values were recorded. Obtained values of tensile force were on the first plot approximately 30 kN and on the second plot 54,3 kN. Interdependence values of tensile forces between internal and external

Název v anglickém jazyce

Measurement of tensile force at the fundamental tillage using tractor?s build -in sensor and external sensor connected between machines and their comparison

Popis výsledku anglicky

The value of tensile force during soil tillage is crucial for estimation of the energy performance of trailed machines. For tensile force measurements was used mouldboard plough with working width of 4 m. The ploughing speed was approximately 7 kmh-1. The measurement was carried out on two plots that showed different soil texture. On the first plot dominate loam-sandy soil whereas on the second plot clay soil, the slopes of the plots are 1,1 and 2,4 respectively. Both plots have been left without modification of stubble after harvest. To measure the tensile forces was used the dynamometer LUKAS type S-38. Dynamometer was placed in a hinge, which was positioned between two tractors. As a second method of tensile force measurement was used from electro-hydraulic hitch sensors from where the values were recorded. Obtained values of tensile force were on the first plot approximately 30 kN and on the second plot 54,3 kN. Interdependence values of tensile forces between internal and external

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

GB - Zemědělské stroje a stavby

OECD FORD obor

—

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Agronomy Research

ISSN

1406-894X

e-ISSN

—

Svazek periodika

13

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

95-100

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—