Steel cutting using abrasive water jet

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41310%2F17%3A74857" target="_blank" >RIV/60460709:41310/17:74857 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.22616/ERDev2017.16.N014" target="_blank" >http://dx.doi.org/10.22616/ERDev2017.16.N014</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.22616/ERDev2017.16.N014" target="_blank" >10.22616/ERDev2017.16.N014</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Steel cutting using abrasive water jet

Popis výsledku v původním jazyce

Technology of material parting using water of high pressure is considered as a modern and perspective method. It makes possible parting of practically all non-metallic as well as metallic materials. According to the type, properties and thickness of the parted material two methods are used, namely (pure) water jet machining and abrasive water jet machining. This article contains the machining test results of steel sheets of different thickness (5 to 20 mm) at different machining parameters. On the tests the influences of the machining speed (10 to 425 mm/min) and of the abrasive amount (211,5 to 417,8 g/min) on the cut width were observed. The cut was observed primarily at the water jet input and output. The deviation from the perpendicular line was observed, too. It was proved that the machining speed influences primarily the cut width and the deviation from the perpendicular line. The abrasive amount is of lesser importance. Kerf width ranges from about 1,05 to 1,15 mm (for a plate thickness of 5

Název v anglickém jazyce

Steel cutting using abrasive water jet

Popis výsledku anglicky

Technology of material parting using water of high pressure is considered as a modern and perspective method. It makes possible parting of practically all non-metallic as well as metallic materials. According to the type, properties and thickness of the parted material two methods are used, namely (pure) water jet machining and abrasive water jet machining. This article contains the machining test results of steel sheets of different thickness (5 to 20 mm) at different machining parameters. On the tests the influences of the machining speed (10 to 425 mm/min) and of the abrasive amount (211,5 to 417,8 g/min) on the cut width were observed. The cut was observed primarily at the water jet input and output. The deviation from the perpendicular line was observed, too. It was proved that the machining speed influences primarily the cut width and the deviation from the perpendicular line. The abrasive amount is of lesser importance. Kerf width ranges from about 1,05 to 1,15 mm (for a plate thickness of 5

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

16th International Scientific Conference Engineering for Rural Development

ISBN

—

ISSN

1691-3043

e-ISSN

1691-5976

Počet stran výsledku

7

Strana od-do

75-81

Název nakladatele

Latvia University of Agriculture

Místo vydání

Jelgava, Latvia

Místo konání akce

Jelgava

Datum konání akce

24. 5. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000416378300010