SURFACE WAVINESS OF MEDIUM-DENSITY FIBERBOARD AND EDGE-GLUED PANEL AFTER EDGE MILLING

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41320%2F17%3A74856" target="_blank" >RIV/60460709:41320/17:74856 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

SURFACE WAVINESS OF MEDIUM-DENSITY FIBERBOARD AND EDGE-GLUED PANEL AFTER EDGE MILLING

Popis výsledku v původním jazyce

This article deal with investigation of mean arithmetic deviation of the waviness profile (Wa) on edge surface after edge milling of medium-density fiberboard, medium-density fiberboard with single-sided lamination and spruce edge-glued panel. Edge milling afftected feed rate 4, 8, and 11 m.min(-1) and cutting speed 20, 30, 40 a 60 m.s(-1). There were used for milling 3 types of tungsteen carbide blades with different composition and treatment (HW1, HW2 and HW1 + CrTiN coating). Working results show that the lowest values of waviness were found with a spruce glulam. Considering the machined surface quality the most suitable blade is HW1, then HW1 + CrTiN coating and the worst one is HW2. The lowest measured values of Wa were found with the feed rate of 4 m.min(-1) and cutting speed of 60 m.s(-1). The increase in cutting speed resulted in the drop in the values of average Wa, while the increase in feed rate had the opposite effect.

Název v anglickém jazyce

SURFACE WAVINESS OF MEDIUM-DENSITY FIBERBOARD AND EDGE-GLUED PANEL AFTER EDGE MILLING

Popis výsledku anglicky

This article deal with investigation of mean arithmetic deviation of the waviness profile (Wa) on edge surface after edge milling of medium-density fiberboard, medium-density fiberboard with single-sided lamination and spruce edge-glued panel. Edge milling afftected feed rate 4, 8, and 11 m.min(-1) and cutting speed 20, 30, 40 a 60 m.s(-1). There were used for milling 3 types of tungsteen carbide blades with different composition and treatment (HW1, HW2 and HW1 + CrTiN coating). Working results show that the lowest values of waviness were found with a spruce glulam. Considering the machined surface quality the most suitable blade is HW1, then HW1 + CrTiN coating and the worst one is HW2. The lowest measured values of Wa were found with the feed rate of 4 m.min(-1) and cutting speed of 60 m.s(-1). The increase in cutting speed resulted in the drop in the values of average Wa, while the increase in feed rate had the opposite effect.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20502 - Paper and wood

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Wood Research

ISSN

1336-4561

e-ISSN

—

Svazek periodika

62

Číslo periodika v rámci svazku

3

Stát vydavatele periodika

SK - Slovenská republika

Počet stran výsledku

12

Strana od-do

459-470

Kód UT WoS článku

000406540900011

EID výsledku v databázi Scopus

2-s2.0-85025818709