Power Consumption during Edge Milling of Medium-Density Fiberboard and Edge-Glued Panel

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41320%2F17%3A74867" target="_blank" >RIV/60460709:41320/17:74867 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Power Consumption during Edge Milling of Medium-Density Fiberboard and Edge-Glued Panel

Popis výsledku v původním jazyce

This paper presents the energy consumption differences during the edge milling of various board materials (medium-density fiberboard (MDF), medium-density fiberboard with single-sided lamination (MDF-L), and spruce edge-glued panel (SEGP)). The edge milling was carried out with various parameters: feed rate (4, 8, and 11 m/min), cutting speed (20, 30, 40, and 60 m/s), and blade type (tungsten carbide HW1, HW2, and HW1 coated with CrTiN (HW1 + CrTiN)). The results indicated that the increase in the cutting speed and feed rate cause the increase in cutting power. The highest cutting power values were observed with the milling of MDF, slightly lower values were observed with MDF-L, and the lowest values were observed with SEGP. Very similar cutting power values during milling were noted with HW1 and HW2 blades, whereas milling with the HW1 + CrTiN resulted in slightly higher values (e.g., 1% higher).

Název v anglickém jazyce

Power Consumption during Edge Milling of Medium-Density Fiberboard and Edge-Glued Panel

Popis výsledku anglicky

This paper presents the energy consumption differences during the edge milling of various board materials (medium-density fiberboard (MDF), medium-density fiberboard with single-sided lamination (MDF-L), and spruce edge-glued panel (SEGP)). The edge milling was carried out with various parameters: feed rate (4, 8, and 11 m/min), cutting speed (20, 30, 40, and 60 m/s), and blade type (tungsten carbide HW1, HW2, and HW1 coated with CrTiN (HW1 + CrTiN)). The results indicated that the increase in the cutting speed and feed rate cause the increase in cutting power. The highest cutting power values were observed with the milling of MDF, slightly lower values were observed with MDF-L, and the lowest values were observed with SEGP. Very similar cutting power values during milling were noted with HW1 and HW2 blades, whereas milling with the HW1 + CrTiN resulted in slightly higher values (e.g., 1% higher).

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20502 - Paper and wood

Projekt

<a href="/cs/project/QJ1330233" target="_blank" >QJ1330233: Příprava legislativních, hospodářsko-úpravnických, mysliveckých a pěstitelsko-ochranářských rámců jako nástrojů adaptace lesního hospodářství na změny přírodních a společenských podmínek</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

BioResources

ISSN

1930-2126

e-ISSN

—

Svazek periodika

12

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

14

Strana od-do

7413-7426

Kód UT WoS článku

000422879900038

EID výsledku v databázi Scopus

2-s2.0-85032681150