MEDIUM-DENSITY FIBERBOARD AND EDGE-GLUED PANEL AFTER EDGE MILLING - SURFACE WAVINESS AFTER MACHINING WITH DIFFERENT PARAMETERS MEASURED BY CONTACT AND CONTACTLESS METHOD
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41320%2F18%3A78598" target="_blank" >RIV/60460709:41320/18:78598 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
MEDIUM-DENSITY FIBERBOARD AND EDGE-GLUED PANEL AFTER EDGE MILLING - SURFACE WAVINESS AFTER MACHINING WITH DIFFERENT PARAMETERS MEASURED BY CONTACT AND CONTACTLESS METHOD
Popis výsledku v původním jazyce
This article deals with the quality of the milled surface of board edges. The quality is evaluated using the Wa (mean arithmetic deviation of the surface waviness). The Wa was measured by two methods (contact and contactless). Form Talysurf 50 Intra was used for the contact method, and the LEXT 3D measuring laser microscope OLS4100 was used for the contactless method. The variable factors whose effect on the resulting waviness was determined were the machined material, milling cutters, cutting speed and feed rate. The boards used were mediumdensity fiberboard, medium-density fiberboard with single-sided lamination and spruce edgeglued panel. Three different cutters were used for the milling, all of which were made of sintered carbide, and one of them was coated (CrTiN). The cutting speeds were 20, 30, 40 and 60 m.s(-1), and the feed rates were 4, 8 and 11 m.min(-1). All the above-mentioned factors as well as their mutual interaction had an effect on the waviness. There was no significant differ
Název v anglickém jazyce
MEDIUM-DENSITY FIBERBOARD AND EDGE-GLUED PANEL AFTER EDGE MILLING - SURFACE WAVINESS AFTER MACHINING WITH DIFFERENT PARAMETERS MEASURED BY CONTACT AND CONTACTLESS METHOD
Popis výsledku anglicky
This article deals with the quality of the milled surface of board edges. The quality is evaluated using the Wa (mean arithmetic deviation of the surface waviness). The Wa was measured by two methods (contact and contactless). Form Talysurf 50 Intra was used for the contact method, and the LEXT 3D measuring laser microscope OLS4100 was used for the contactless method. The variable factors whose effect on the resulting waviness was determined were the machined material, milling cutters, cutting speed and feed rate. The boards used were mediumdensity fiberboard, medium-density fiberboard with single-sided lamination and spruce edgeglued panel. Three different cutters were used for the milling, all of which were made of sintered carbide, and one of them was coated (CrTiN). The cutting speeds were 20, 30, 40 and 60 m.s(-1), and the feed rates were 4, 8 and 11 m.min(-1). All the above-mentioned factors as well as their mutual interaction had an effect on the waviness. There was no significant differ
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20502 - Paper and wood
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Wood Research
ISSN
1336-4561
e-ISSN
—
Svazek periodika
63
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
SK - Slovenská republika
Počet stran výsledku
15
Strana od-do
683-697
Kód UT WoS článku
000443173100013
EID výsledku v databázi Scopus
2-s2.0-85052953623