Surface quality measurement by contact and laser methods on thermally modified spruce wood after plain milling
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41320%2F20%3A84670" target="_blank" >RIV/60460709:41320/20:84670 - isvavai.cz</a>
Výsledek na webu
<a href="https://link.springer.com/article/10.1007/s00170-020-05983-7" target="_blank" >https://link.springer.com/article/10.1007/s00170-020-05983-7</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1007/s00170-020-05983-7" target="_blank" >10.1007/s00170-020-05983-7</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Surface quality measurement by contact and laser methods on thermally modified spruce wood after plain milling
Popis výsledku v původním jazyce
The accuracy and reliability of a measuring device is crucial to determine the quality of wood surface. This paper compares the surface quality of thermally modified spruce wood measured by two different methods. Spruce wood specimens were thermally modified at different temperatures (160, 180, and 210 degrees C) and then milled with a single-spindle milling machine operated at different combinations of processing parameters (cutting speed, rake angle, and feed rate). Surface quality (surface roughness and surface waviness) of the specimens were measured by laser as well as contact method. Higher values of surface roughness and waviness were obtained by the laser method compared with the contact method. Average surface roughness was 31% higher, while average waviness was 35% higher in laser method as compared with the contact method. Based on the surface quality obtained by laser method and energy consumption during milling, the optimum combination of parameters for milling of thermally modified spru
Název v anglickém jazyce
Surface quality measurement by contact and laser methods on thermally modified spruce wood after plain milling
Popis výsledku anglicky
The accuracy and reliability of a measuring device is crucial to determine the quality of wood surface. This paper compares the surface quality of thermally modified spruce wood measured by two different methods. Spruce wood specimens were thermally modified at different temperatures (160, 180, and 210 degrees C) and then milled with a single-spindle milling machine operated at different combinations of processing parameters (cutting speed, rake angle, and feed rate). Surface quality (surface roughness and surface waviness) of the specimens were measured by laser as well as contact method. Higher values of surface roughness and waviness were obtained by the laser method compared with the contact method. Average surface roughness was 31% higher, while average waviness was 35% higher in laser method as compared with the contact method. Based on the surface quality obtained by laser method and energy consumption during milling, the optimum combination of parameters for milling of thermally modified spru
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20502 - Paper and wood
Návaznosti výsledku
Projekt
<a href="/cs/project/EF16_019%2F0000803" target="_blank" >EF16_019/0000803: Excelentní Výzkum jako podpora Adaptace lesnictví a dřevařství na globální změnu a 4. průmyslovou revoluci</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2020
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
International Journal of Advanced Manufacturing Technology
ISSN
0268-3768
e-ISSN
—
Svazek periodika
110
Číslo periodika v rámci svazku
5-6
Stát vydavatele periodika
GB - Spojené království Velké Británie a Severního Irska
Počet stran výsledku
11
Strana od-do
1653-1663
Kód UT WoS článku
000563165600005
EID výsledku v databázi Scopus
2-s2.0-85089866507