Optimization of solder paste quantity considering the properties of solder joints

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23220%2F17%3A43930925" target="_blank" >RIV/49777513:23220/17:43930925 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.emeraldinsight.com/doi/full/10.1108/SSMT-10-2016-0025" target="_blank" >http://www.emeraldinsight.com/doi/full/10.1108/SSMT-10-2016-0025</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1108/SSMT-10-2016-0025" target="_blank" >10.1108/SSMT-10-2016-0025</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Optimization of solder paste quantity considering the properties of solder joints

Popis výsledku v původním jazyce

Purpose – The purpose of this paper is to find an optimum between the quantity of solder paste and the desired properties of the soldered joint. A reduction of solder paste quantity is recognized as an opportunity to save money. On the other hand, the quantity of solder paste significantly influences the final properties of the soldered joint. The purpose is also to design recommendations for manufacturers of electronic assemblies. Design/methodology/approach – The processing of the paper was initiated by a literature review. The expert analysis was the next step. The result of analysis was a fishbone diagram. Subsequently, the experiment was designed. Seven types and three volume of solder pastes and two aperture shapes of the stencil were used. The measured parameters were mechanical strength, electrical resistance, voids area and intermetallic compound (IMC) thicknesses. The results of the experiment were evaluated and recommendations for practice were defined. Findings – The carried out research has confirmed the influence of solder paste quantity on the shear strength, electrical resistance, voids area and IMC thickness of solder joint. The article presents the results achieved for solders Sn42Bi58, Sn42Bi57.6Ag0.4, SnAg3.0Cu0.5, SnCu0.7Ag1.0NiGe, SnAg3.5Bi0.5In8.0 and Sn62.5Pb36.5Ag1.0. Reduction of solder paste quantity down to 74 per cent (i.e. one quarter of quantity) decreases mechanical shear strength less than 10 per cent. Recommendations relating to the optimal reduction of solder paste quantity have been designed for each solder paste. Originality/value – Contribution of the paper is impact assessment of solder paste quantity on the properties of the soldered joint. It was carried out a large number of experiments and measurements which verify this effect. Such a comprehensive overview of the results is not yet available in the literature. Recommendations for manufacturers of electronic assemblies are also the benefit of article.

Název v anglickém jazyce

Optimization of solder paste quantity considering the properties of solder joints

Popis výsledku anglicky

Purpose – The purpose of this paper is to find an optimum between the quantity of solder paste and the desired properties of the soldered joint. A reduction of solder paste quantity is recognized as an opportunity to save money. On the other hand, the quantity of solder paste significantly influences the final properties of the soldered joint. The purpose is also to design recommendations for manufacturers of electronic assemblies. Design/methodology/approach – The processing of the paper was initiated by a literature review. The expert analysis was the next step. The result of analysis was a fishbone diagram. Subsequently, the experiment was designed. Seven types and three volume of solder pastes and two aperture shapes of the stencil were used. The measured parameters were mechanical strength, electrical resistance, voids area and intermetallic compound (IMC) thicknesses. The results of the experiment were evaluated and recommendations for practice were defined. Findings – The carried out research has confirmed the influence of solder paste quantity on the shear strength, electrical resistance, voids area and IMC thickness of solder joint. The article presents the results achieved for solders Sn42Bi58, Sn42Bi57.6Ag0.4, SnAg3.0Cu0.5, SnCu0.7Ag1.0NiGe, SnAg3.5Bi0.5In8.0 and Sn62.5Pb36.5Ag1.0. Reduction of solder paste quantity down to 74 per cent (i.e. one quarter of quantity) decreases mechanical shear strength less than 10 per cent. Recommendations relating to the optimal reduction of solder paste quantity have been designed for each solder paste. Originality/value – Contribution of the paper is impact assessment of solder paste quantity on the properties of the soldered joint. It was carried out a large number of experiments and measurements which verify this effect. Such a comprehensive overview of the results is not yet available in the literature. Recommendations for manufacturers of electronic assemblies are also the benefit of article.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20201 - Electrical and electronic engineering

Projekt

<a href="/cs/project/LO1607" target="_blank" >LO1607: RICE – Nové technologie a koncepce pro inteligentní průmyslové systémy</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Soldering &amp; Surface Mount Technology

ISSN

0954-0911

e-ISSN

—

Svazek periodika

29

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

8

Strana od-do

15-22

Kód UT WoS článku

000396464600004

EID výsledku v databázi Scopus

2-s2.0-85011112580