Electron reflectivity from clean and oxidized steel surface

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081731%3A_____%2F22%3A00565515" target="_blank" >RIV/68081731:_____/22:00565515 - isvavai.cz</a>

Výsledek na webu

<a href="https://analyticalsciencejournals.onlinelibrary.wiley.com/doi/10.1002/sia.7079" target="_blank" >https://analyticalsciencejournals.onlinelibrary.wiley.com/doi/10.1002/sia.7079</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1002/sia.7079" target="_blank" >10.1002/sia.7079</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Electron reflectivity from clean and oxidized steel surface

Popis výsledku v původním jazyce

This paper aims to elucidate the effect of an air-formed native oxide covering mild steel surface on the contrast in the scanning electron microscopy (SEM) images obtained with the landing energy from 5 keV down to 0 eV. Part of the mild steel surface was in-situ cleaned by Ar+ ion sputtering process in order to remove native oxide from the surface. It enabled us to observe the oxide-free and the naturally oxidized area on the mild steel surface simultaneously in the SEM micrographs. Presence of the native oxide starts to play a role in the SEM images acquired at landing energy below roughly 3 keV. Contrast between differently oriented grains situated inside the area covered by the native oxide starts to be negligible with landing energy decreasing below 3 keV, up to some ultra-low values where the contrast increases again. Total reflectivity contrast between the clean and the oxidized area increases exponentially with landing energy decreasing below 3 keV. The reflectivity-versus-energy curves of the cleaned and the naturally oxidized mild steel surface are markedly different. The reflectivity of the electrons is correlated with the density of states (DOS), as is demonstrated at very low landing energies. Sensitivity of the very low-energy electrons to the electronic structure was verified by comparison of the experimental data with the simulations of reflectivities, band structure, and DOS. The theoretical predictions are based on the density-functional theory calculations and they have been performed in energy range corresponding to specular reflectivities of the Fe-BCC (001) orientation. We have also observed that close to the mirror condition, that is, near-zero landing energies, the primary electrons become sensitive to the surface potential differences caused by the work function differences of clean and native oxide-covered steel surfaces.

Název v anglickém jazyce

Electron reflectivity from clean and oxidized steel surface

Popis výsledku anglicky

This paper aims to elucidate the effect of an air-formed native oxide covering mild steel surface on the contrast in the scanning electron microscopy (SEM) images obtained with the landing energy from 5 keV down to 0 eV. Part of the mild steel surface was in-situ cleaned by Ar+ ion sputtering process in order to remove native oxide from the surface. It enabled us to observe the oxide-free and the naturally oxidized area on the mild steel surface simultaneously in the SEM micrographs. Presence of the native oxide starts to play a role in the SEM images acquired at landing energy below roughly 3 keV. Contrast between differently oriented grains situated inside the area covered by the native oxide starts to be negligible with landing energy decreasing below 3 keV, up to some ultra-low values where the contrast increases again. Total reflectivity contrast between the clean and the oxidized area increases exponentially with landing energy decreasing below 3 keV. The reflectivity-versus-energy curves of the cleaned and the naturally oxidized mild steel surface are markedly different. The reflectivity of the electrons is correlated with the density of states (DOS), as is demonstrated at very low landing energies. Sensitivity of the very low-energy electrons to the electronic structure was verified by comparison of the experimental data with the simulations of reflectivities, band structure, and DOS. The theoretical predictions are based on the density-functional theory calculations and they have been performed in energy range corresponding to specular reflectivities of the Fe-BCC (001) orientation. We have also observed that close to the mirror condition, that is, near-zero landing energies, the primary electrons become sensitive to the surface potential differences caused by the work function differences of clean and native oxide-covered steel surfaces.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/TN01000008" target="_blank" >TN01000008: Centrum elektronové a fotonové optiky</a><br>

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2022

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Surface and Interface Analysis

ISSN

0142-2421

e-ISSN

1096-9918

Svazek periodika

54

Číslo periodika v rámci svazku

6

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

10

Strana od-do

667-676

Kód UT WoS článku

000760336000001

EID výsledku v databázi Scopus

2-s2.0-85125073168