The thermal effect of unconventional cutting technologies on steel DIN 1.7102

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F20%3A63525318" target="_blank" >RIV/70883521:28110/20:63525318 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/70883521:28140/20:63525318

Výsledek na webu

<a href="https://www.scientific.net/MSF.994.78" target="_blank" >https://www.scientific.net/MSF.994.78</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/msf.994.78" target="_blank" >10.4028/www.scientific.net/msf.994.78</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The thermal effect of unconventional cutting technologies on steel DIN 1.7102

Popis výsledku v původním jazyce

New technologies known as unconventional technologies make it possible to cut complex shapes at high speed and with relatively high precision. In many cases, especially in the case of thin sheet, created parts produced do not require any further treatment by post-machining. Knowledge of the accompanying phenomena, such as the heat-affected zone (HAZ) or the surface quality of the cutting edge, is necessary, for example, to assess further machining of material in these areas (e.g. drilling and reaming holes or finishing operations on the cutting edge). In this study, the thermal effect of four unconventional cutting technologies – laser, plasma, wire electrical discharge machining (wire EDM) and waterjet cutting on the cut surface of steel sheets is investigated. Steel 1.7102 (DIN 54SiCr6) was chosen for purpose of this study. The width of the HAZ and the nanohardness beneath the cut surface were analyzed. © 2020 Trans Tech Publications Ltd, Switzerland.

Název v anglickém jazyce

The thermal effect of unconventional cutting technologies on steel DIN 1.7102

Popis výsledku anglicky

New technologies known as unconventional technologies make it possible to cut complex shapes at high speed and with relatively high precision. In many cases, especially in the case of thin sheet, created parts produced do not require any further treatment by post-machining. Knowledge of the accompanying phenomena, such as the heat-affected zone (HAZ) or the surface quality of the cutting edge, is necessary, for example, to assess further machining of material in these areas (e.g. drilling and reaming holes or finishing operations on the cutting edge). In this study, the thermal effect of four unconventional cutting technologies – laser, plasma, wire electrical discharge machining (wire EDM) and waterjet cutting on the cut surface of steel sheets is investigated. Steel 1.7102 (DIN 54SiCr6) was chosen for purpose of this study. The width of the HAZ and the nanohardness beneath the cut surface were analyzed. © 2020 Trans Tech Publications Ltd, Switzerland.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials Science Forum

ISSN

0255-5476

e-ISSN

—

Svazek periodika

994

Číslo periodika v rámci svazku

Neuveden

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

10

Strana od-do

78-87

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85086755797